How does the atomic hydrogen or oxy-hydrogen torch function for cutting and welding purposes? Explain.
Atomic hydrogen atoms are produced by the dissociation of dihydrogen with the help of an electric arc. This releases a huge amount of energy (435.88 kJ mol-1). This energy can be used to generate a temperature of 4000 K, which is ideal for welding and cutting metals. Hence, atomic hydrogen or oxy-hydrogen torches are used for these purposes. For this reason, atomic hydrogen is allowed to recombine on the surface to be welded to generate the desired temperature.
Justify the position of hydrogen in the periodic table on the basis of its electronic configuration.
Compare the structures of H2O and H2O2.
Write chemical reactions to show the amphoteric nature of water.
Arrange the following
(i) CaH2, BeH2 and TiH2 in order of increasing electrical conductance.
(ii) LiH, NaH and CsH in order of increasing ionic character.
(iii) H-H, D-D and F-F in order of increasing bond dissociation enthalpy.
(iv) NaH, MgH2 and H2O in order of increasing reducing property.
Discuss the principle and method of softening of hard water by synthetic ion-exchange resins.
What do you understand by the term “non-stoichiometric hydrides”? Do you expect this type of the hydrides to be formed by alkali metals? Justify your answer.
What is meant by 'demineralised' water and how can it be obtained?
What causes the temporary and permanent hardness of water?
How does H2O2 behave as a bleaching agent?
Why does hydrogen occur in a diatomic form rather than in a monoatomic form under normal conditions?
How do you account for the formation of ethane during chlorination of methane?
What are hybridisation states of each carbon atom in the following compounds ?
(i) CH2=C=O,
(ii) CH3CH=CH2,
(iii) (CH3)2CO,
(iv) CH2=CHCN,
(v) C6H6
What will be the minimum pressure required to compress 500 dm3 of air at 1 bar to 200 dm3 at 30°C?
What are the common physical and chemical features of alkali metals?
Calculate the molecular mass of the following:
(i) H2O
(ii) CO2
(iii) CH4
Assign oxidation number to the underlined elements in each of the following species:
(a) NaH2PO4
(b) NaHSO4
(c) H4P2O7
(d) K2MnO4
(e) CaO2
(f) NaBH4
(g) H2S2O7
(h) KAl(SO4)2.12 H2O
What is the basic theme of organisation in the periodic table?
Explain the formation of a chemical bond.
Choose the correct answer. A thermodynamic state function is a quantity
(i) used to determine heat changes
(ii) whose value is independent of path
(iii) used to determine pressure volume work
(iv) whose value depends on temperature only.
A liquid is in equilibrium with its vapour in a sealed container at a fixed temperature. The volume of the container is suddenly increased.
a) What is the initial effect of the change on vapour pressure?
b) How do rates of evaporation and condensation change initially?
c) What happens when equilibrium is restored finally and what will be the final vapour pressure?
Describe the change in hybridisation (if any) of the Al atom in the following reaction.
Explain why alkali and alkaline earth metals cannot be obtained by chemical reduction methods?
Which of the following carbocation is most stable ?
Calcium carbonate reacts with aqueous HCl to give CaCl2 and CO2 according to the reaction,
CaCO3(s) + 2 HCl(aq) → CaCl2(aq) + CO2(g) + H2O(l)
What mass of CaCO3 is required to react completely with 25 mL of 0.75 M HCl?
Indicate the σ and π bonds in the following molecules :
(i) C6H6,
(ii) C6H12,
(iii) CH2Cl2,
(iv) CH2=C=CH2,
(v) CH3NO2,
(vi) HCONHCH3
What are the reactions involved for ozone layer depletion in the stratosphere?
Describe the theory associated with the radius of an atom as it
(a) gains an electron
(b) loses an electron
Why are alkali metals not found in nature?
Pressure is determined as force per unit area of the surface. The SI unit of pressure, Pascal is as shown below:
1Pa = 1N m–2
If mass of air at sea level is 1034 g cm–2, calculate the pressure in Pascal.
What is the maximum number of emission lines when the excited electron of an H atom in n = 6 drops to the ground state?