Class 12 Chemistry - Chapter Coordination Compounds NCERT Solutions | Write down the IUPAC name for each of th

[NiCl₄]^2- is paramagnetic while [Ni(CO)₄] is diamagnetic though both are tetrahedral. Why?

Explain on the basis of valence bond theory that [Ni(CN)₄]^2- ion with square planar structure is diamagnetic and the [Ni(CN)₄]^2- ion with tetrahedral geometry is paramagnetic.

Draw figure to show the splitting of d orbitals in an octahedral crystal field.

[Cr(NH₃)₆]³⁺ is paramagnetic while [Ni(CN)₄]^2- is diamagnetic.  Explain why?

The oxidation number of cobalt in K[Co(CO)₄] is

(i) +1

(ii) +3

(iii) -1

(iv) -3

Discuss the nature of bonding in metal carbonyls.

Discuss the nature of bonding in the following coordination entities on the basis of valence bond theory:

(i) [Fe(CN)₆]^4-

(ii) [FeF₆]^3-

(iii) [Co(C₂O₄)3]^3-

(iv) [CoF₆]^3-

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

Predict the number of unpaired electrons in the square planar [Pt(CN)₄]^2- ion.

Using IUPAC norms write the formulas for the following:

(i) Tetrahydroxozincate(II)

(ii) Potassium tetrachloridopalladate(II)

(iii) Diamminedichloridoplatinum(II)

(iv) Potassium tetracyanonickelate(II)

(v) Pentaamminenitrito-O-cobalt(III)

(vi) Hexaamminecobalt(III) sulphate

(vii) Potassium tri(oxalato)chromate(III)

(viii) Hexaammineplatinum(IV)

(ix) Tetrabromidocuprate(II)

(x) Pentaamminenitrito-N-cobalt(III)

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

Write structures of the following compounds:

(i) 2-Chloro-3-methylpentane

(ii) 1-Chloro-4-ethylcyclohexane

(iii) 4-tert. Butyl-3-iodoheptane

(iv) 1,4-Dibromobut-2-ene

(v) 1-Bromo-4-sec. butyl-2-methylbenzene

The E^θ(M²⁺/M) value for copper is positive (+0.34V). What is possibly the reason for this? (Hint: consider its high Δ_aHV and low Δ_hydHV)

The decomposition of dimethyl ether leads to the formation of CH₄, H₂and CO and the reaction rate is given by

Rate = k [CH₃OCH₃]^3/2

The rate of reaction is followed by increase in pressure in a closed vessel, so the rate can also be expressed in terms of the partial pressure of dimethyl ether, i.e.,

 Rate = k (P_CH3OCH3)^3/2

If the pressure is measured in bar andtime in minutes, then what are the units of rate and rate constants?

What are essential and non-essential amino acids? Give two examples ofeach type.

Benzene and toluene form ideal solution over the entire range of composition. The vapour pressure of pure benzene and toluene at 300 K are 50.71 mm Hg and 32.06 mm Hg respectively. Calculate the mole fraction of benzene in vapour phase if 80 g of benzene is mixed with 100 g of toluene.

Which is a stronger reducing agent Cr²⁺ or Fe²⁺ and why?

Why has it been difficult to study the chemistry of radon?

Give examples and suggest reasons for the following features of the transition metal chemistry:

(i)The lowest oxide of transition metal is basic, the highest is amphoteric/acidic.

(ii)A transition metal exhibits highest oxidation state in oxides and fluorides.

(iii) The highest oxidation state is exhibited in oxoanions of a metal.

What are interstitial compounds? Why are such compounds well known for transition metals?

Predict the major product of acid catalysed dehydration of

(i) 1-Methylcyclohexanol and

(ii) Butan-1-ol

How are polymers classified on the basis of structure?