Class 12 Chemistry - Chapter General Principles and Processes of Isolation of Elements NCERT Solutions | Describe a method for refining nickel.

What is the significance of leaching in the extraction of aluminium?

Write down the reactions taking place in different zones in the blast furnace during the extraction of iron.

Copper can be extracted by hydrometallurgy but not zinc. Explain.

Outline the principles of refining of metals by the following methods:

(i) Zone refining

(ii) Electrolytic refining

(iii) Vapour phase refining

Name the common elements present in the anode mud in electrolytic refining of copper. Why are they so present ?

The reaction,

      Cr₂O₃  +  2Al    →    Al₂O₃  + 2Cr            (ΔG_o = -421kJ)

is thermodynamically feasible as is apparent from the Gibbs energy value. Why does it not take place at room temperature?

How can you separate alumina from silica in bauxite ore associated with silica? Give equations, if any.

Why is the extraction of copper from pyrites more difficult than that from its oxide ore through reduction?

Write chemical reactions taking place in the extraction of zinc from zinc blende.

Why copper matte is put in silica lined converter?

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

Write structures of the following compounds:

(i) 2-Chloro-3-methylpentane

(ii) 1-Chloro-4-ethylcyclohexane

(iii) 4-tert. Butyl-3-iodoheptane

(iv) 1,4-Dibromobut-2-ene

(v) 1-Bromo-4-sec. butyl-2-methylbenzene

Write the monomers used for getting the following polymers. (i) Polyvinyl chloride (ii) Teflon (iii) Bakelite

How would you account for the following:

(i) Of the d⁴ species, Cr²⁺ is strongly reducing while manganese (III) is strongly oxidising.

(ii) Cobalt (II) is stable in aqueous solution but in the presence of complexing reagents it is easily oxidised.

(iii) The d¹ configuration is very unstable in ions.

How is the variability in oxidation states of transition metals different from that of the non-transition metals? Illustrate with examples.

Predict which of the following will be coloured in aqueous solution?

Ti³⁺, V³⁺, Cu⁺, Sc³⁺, Mn²⁺, Fe³⁺ and Co²⁺.

Give reasons for each.

Arrange the following polymers in increasing order of their intermolecular forces.
(i) Nylon 6, 6, Buna-S, Polythene.
(ii) Nylon 6, Neoprene, Polyvinyl chloride.

Explain why propanol has higher boiling point than that of the hydrocarbon, butane?

Actinoid contraction is greater from element to element than lanthanoid contraction. Why?

How can you determine the atomic mass of an unknown metal if you know its density and the dimension of its unit cell? Explain.

How would you determine the standard electrode potential of the system Mg²⁺ | Mg?

Explain giving reasons:

(i) Transition metals and many of their compounds show paramagnetic behaviour.

(ii) The enthalpies of atomisation of the transition metals are high.

(iii) The transition metals generally form coloured compounds.

(iv) Transition metals and their many compounds act as good catalyst.