Class 12 Chemistry - Chapter Solutions NCERT Solutions | Define the following terms: (i) Mole

A 5% solution (by mass) of cane sugar in water has freezing point of 271 K. Calculate the freezing point of 5% glucose in water if freezing point of pure water is 273.15 K.

A solution of glucose in water is labelled as 10% w/w, what would be the molality and mole fraction of each component in the solution? If the density of solution is 1.2 g mL^-1, then what shall be the molarity of the solution?

Henry's law constant for CO₂ in water is 1.67 x 10⁸Pa at 298 K. Calculate the quantity of CO₂in 500 mL of soda water when packed under 2.5 atm CO₂ pressure at 298 K.

Calculate the mass of a non-volatile solute (molar mass 40 g mol^-1) which should be dissolved in 114 g octane to reduce its vapour pressure to 80%.

The vapour pressure of pure liquids A and B are 450 and 700 mm Hg respectively, at 350 K. Find out the composition of the liquid mixture if total vapour pressure is 600 mm Hg. Also find the composition of the vapour phase.

Calculate the mole fraction of benzene in solution containing 30% by mass in carbon tetrachloride.

How many mL of 0.1 M HCl are required to react completely with 1 g mixture of Na₂CO₃ and NaHCO₃ containing equimolar amounts of both?

H₂S, a toxic gas with rotten egg like smell, is used for the qualitative analysis. If the solubility of H₂S in water at STP is 0.195 m, calculate Henry's law constant.

Boiling point of water at 750 mm Hg is 99.63°C. How much sucrose is to be added to 500 g of water such that it boils at 100°C.Molal elevation constant for water is 0.52 K kg mol^-1.

An aqueous solution of 2% non-volatile solute exerts a pressure of 1.004 bar at the normal boiling point of the solvent. What is the molar mass of the solute?

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

Discuss the trends in chemical reactivity of group 15 elements.

Accomplish the following conversions:

(i) Nitrobenzene to benzoic acid

(ii) Benzene to m-bromophenol

(iii) Benzoic acid to aniline

(iv) Aniline to 2,4,6-tribromofluorobenzene

(v) Benzyl chloride to 2-phenylethanamine

(vi) Chlorobenzene to p-chloroaniline

(vii) Aniline to p-bromoaniline

(viii) Benzamide to toluene

(ix) Aniline to benzyl alcohol.

'Stability of a crystal is reflected in themagnitude of its melting point'. Comment. Collect melting points of solid water, ethyl alcohol, diethyl ether and methane from a data book. What can you say about the intermolecular forces between these molecules?

Give reason why a finely divided substance is more effective as an adsorbent.

Amongst the following, the most stable complex is

(i) [Fe(H₂O)₆]³⁺

(ii) [Fe(NH₃)₆]³⁺

(iii) [Fe(C₂O₄)₃]^3-

(iv) [FeCl₆]^3-

What are the characteristics of the transition elements and why are they called transition elements? Which of the d-block elements may not be regarded as the transition elements?

What role does adsorption play in heterogeneous catalysis?

Can you store copper sulphate solutions in a zinc pot?

How the following conversions can be carried out?

(i) Propene to propan-1-ol

(ii) Ethanol to but-1-yne

(iii) 1-Bromopropane to 2-bromopropane

(iv) Toluene to benzyl alcohol

(v) Benzene to 4-bromonitrobenzene

(vi) Benzyl alcohol to 2-phenylethanoic acid

(vii) Ethanol to propanenitrile

(viii) Aniline to chlorobenzene

(ix) 2-Chlorobutane to 3, 4-dimethylhexane

(x) 2-Methyl-1-propene to 2-chloro-2-methylpropane

(xi) Ethyl chloride to propanoic acid

(xii) But-1-ene to n-butyliodide

(xiii) 2-Chloropropane to 1-propanol

(xiv) Isopropyl alcohol to iodoform

(xv) Chlorobenzene to p-nitrophenol

(xvi) 2-Bromopropane to 1-bromopropane

(xvii) Chloroethane to butane

(xviii) Benzene to diphenyl

(xix) tert-Butyl bromide to isobutyl bromide

(xx) Aniline to phenylisocyanide

The decomposition of hydrocarbon follows the equation

k = (4.5 x 10¹¹ s^-1) e^{-28000 K/T}

Calculate E_a.