Class 12 Chemistry - Chapter Surface Chemistry NCERT Solutions | Discuss the effect of pressure and tempe
Discuss the effect of pressure and temperature on the adsorption of gases on solids.
Effect of pressure & temperature-
According to Le Chatelier’s principle, the magnitude of adsorption should increase with fall in temperature & since adsorption of a gas leads to decrease of pressure, the magnitude of adsorption increases with increase in pressure. If a equilibrium is subjected to a stress, the equilibrium shifts in such a way as to reduce the stress. Graphically, the variation of adsorption with pressure at given constant temperature is given by adsorption isotherm.
The relationship between magnitude of adsorption & pressure can be expressed mathematically by Freundlich Adsorption isotherm i.e a = Kpn where a is the amount of gas adsorbed per unit mass of adsorbent at pressure p & K & n are constant depending upon the nature of gas & adsorbent.The value of n is less than 1 & therefore a does not increase as rapidly as p.
The effect of temperature on the extent of adsorption at a given pressure of adsorbate is given by adsorption isobar.
More Questions From Class 12 Chemistry - Chapter Surface Chemistry
- Q:-
Explain what is observed
(i) When a beam of light is passed through a colloidal sol.
(ii) An electrolyte, NaCl is added to hydrated ferric oxide sol.
(iii) Electric current is passed through a colloidal sol?
- Q:-
Why is adsorption always exothermic?
- Q:-
What do you mean by activity and selectivity of catalysts?
- Q:-
What modification can you suggest in the Hardy-Schulze law?
- Q:-
Explain the following terms:
(i) Electrophoresis
(ii) Coagulation
(iii) Dialysis
(iv) Tyndall effect.
- Q:-
What is an adsorption isotherm? Describe Freundlich adsorption isotherm.
- Q:-
Explain the terms with suitable examples:
(i) Alcosol
(ii) Aerosol
(iii) Hydrosol
- Q:-
How are colloids classified on the basis of
(i) Physical states of components
(ii) Nature of dispersion medium and
(iii) Interaction between dispersed phase and dispersion medium?
- Q:-
Why does physisorption decrease with the increase of temperature
- Q:-
What are the factors which influence the adsorption of a gas on a solid?
Popular Questions of Class 12 Chemistry
- Q:-
For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.
- Q:-
Write the formulas for the following coordination compounds:
(i) Tetraamminediaquacobalt (III) chloride
(ii) Potassium tetracyanonickelate(II)
(iii) Tris(ethane-1,2-diamine) chromium(III) chloride
(iv) Amminebromidochloridonitrito-N-platinate(II)
(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate
(vi) Iron(III) hexacyanoferrate(II)
- Q:-
(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N
(ii) Write IUPAC names of all the isomers.
(iii) What type of isomerism is exhibited by different pairs of amines?
- Q:-
Why are solids rigid?
- Q:-
Write the structures of the following compounds.
(i) α-Methoxypropionaldehyde
(ii) 3-Hydroxybutanal
(iii) 2-Hydroxycyclopentane carbaldehyde
(iv) 4-Oxopentanal
(v) Di-sec-butyl ketone
(vi) 4-Fluoroacetophenone
- Q:-
Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?
- Q:-
Why are pentahalides more covalent than trihalides?
- Q:-
Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?
- Q:-
Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.
- Q:-
Write structures of the following compounds:
(i) 2-Chloro-3-methylpentane
(ii) 1-Chloro-4-ethylcyclohexane
(iii) 4-tert. Butyl-3-iodoheptane
(iv) 1,4-Dibromobut-2-ene
(v) 1-Bromo-4-sec. butyl-2-methylbenzene
Recently Viewed Questions of Class 12 Chemistry
- Q:-
Explain why
(i) the dipole moment of chlorobenzene is lower than that of cyclohexyl chloride?
(ii) alkyl halides, though polar, are immiscible with water?
(iii) Grignard reagents should be prepared under anhydrous conditions?
- Q:-
[NiCl4]2- is paramagnetic while [Ni(CO)4] is diamagnetic though both are tetrahedral. Why?
- Q:-
Give the uses of freon 12, DDT, carbon tetrachloride and iodoform.
- Q:-
With reference to which classification has the statement, ranitidine is an antacid been given?
- Q:-
How will you bring about the following conversions?
(i) Ethanol to but-1-yne
(ii) Ethane to bromoethene
(iii) Propene to 1-nitropropane
(iv) Toluene to benzyl alcohol
(v) Propene to propyne
(vi) Ethanol to ethyl fluoride
(vii) Bromomethane to propanone
(viii) But-1-ene to but-2-ene
(ix) 1-Chlorobutane to n-octane
(x) Benzene to biphenyl.
- Q:-
What type of stoichiometric defect is shown by:
(i) ZnS
(ii) AgBr
- Q:-
Classify the following as addition and condensation polymers: Terylene, Bakelite, Polyvinyl chloride, Polythene.
- Q:-
An aqueous solution of 2% non-volatile solute exerts a pressure of 1.004 bar at the normal boiling point of the solvent. What is the molar mass of the solute?
- Q:-
Give the IUPAC names of the following compounds:
(i) CH3CH(Cl)CH(Br)CH3
(ii) CHF2CBrClF
(iii) ClCH2C≡CCH2Br
(iv) (CCl3)3CCl
(v) CH3C(p-ClC6H4)2CH(Br)CH3
(vi) (CH3)3CCH=CClC6H4I-p
- Q:-
Copper can be extracted by hydrometallurgy but not zinc. Explain.
- All Chapters Of Class 12 Chemistry
- All Subjects Of Class 12