Class 12 Chemistry - Chapter Chemistry in Everyday Life NCERT Solutions | Why should not medicines be taken withou

Why do soaps not work in hard water?

Explain the following terms with suitable examples

(i) cationic detergents

(ii) anionic detergents and

(iii) non-ionic detergents.

What are food preservatives ?

Sleeping pills are recommended by doctors to the patients suffering from sleeplessness but it is not advisable to take its doses without consultation with the doctor, Why?

How do antiseptics differ from disinfectants ? Give one example of each. 

Why is use of aspartame limited to cold foods and drinks?

What are the main constituents of dettol?

With reference to which classification has the statement, ranitidine is an antacid been given?

Write the chemical equation for preparing sodium soap from glyceryl oleate and glyceryl palmitate. Structural formulae of these compounds are given below.

(i) (C₁₅H₃₁COO)₃ C₃H₅ - Glyceryl palmitate

(ii)(C₁₇H₃₃COO)₃ C₃H₅ - Glyceryl oleate

Name a substance which can be used as an antiseptic as well as disinfectant.

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

A cubic solid is made of two elements P and Q. Atoms of Q are at the corners of the cube and P at the body-centre. What is the formula of the compound? What are the coordination numbers of P and Q?

What is the significance of leaching in the extraction of aluminium?

Predict the products of the following reactions:

(i)

(ii)

(iii)

(iv)

Describe a method for refining nickel.

Henry's law constant for the molality of methane in benzene at 298 Kis 4.27 x 10⁵ mm Hg. Calculate the solubility of methane in benzene at 298 Kunder 760 mm Hg.

Discuss the general characteristics of Group 15 elements with reference to their electronic configuration, oxidation state, atomic size, ionisation enthalpy and electronegativity.

Give examples and suggest reasons for the following features of the transition metal chemistry:

(i)The lowest oxide of transition metal is basic, the highest is amphoteric/acidic.

(ii)A transition metal exhibits highest oxidation state in oxides and fluorides.

(iii) The highest oxidation state is exhibited in oxoanions of a metal.

Accomplish the following conversions:

(i) Nitrobenzene to benzoic acid

(ii) Benzene to m-bromophenol

(iii) Benzoic acid to aniline

(iv) Aniline to 2,4,6-tribromofluorobenzene

(v) Benzyl chloride to 2-phenylethanamine

(vi) Chlorobenzene to p-chloroaniline

(vii) Aniline to p-bromoaniline

(viii) Benzamide to toluene

(ix) Aniline to benzyl alcohol.

Indicate the steps in the preparation of:

(i) K₂Cr₂O₇ from chromite ore.

(ii) KMnO₄ from pyrolusite ore.

How are colloids classified on the basis of

(i) Physical states of components

(ii) Nature of dispersion medium and

(iii) Interaction between dispersed phase and dispersion medium?