Suggest two methods to find out wind direction at a given place.
Methods to find the direction of wind are following:
(a) Take a handful of sand or dust. Leave the sand from a height and observe the direction in which sand is moving which will show the direction of wind.
(b) While flying a kite, the direction in which the kite flies shall be the wind direction.
(c) Lift a piece of paper in the air. Now observe the direction of the flying paper, the direction will be the accurate direction of wind.
Classify the changes involved in the following processes as physical or chemical changes:
(a) Photosynthesis
(b) Dissolving sugar in water
(c) Burning of coal
(d) Melting of wax
(e) Beating aluminium to make aluminium foil
(f ) Digestion of food
Given below is a crossword puzzle based on this lesson. Use hints to fill in the blank spaces with letters that complete the words.
Down Across
(D) 1 : Thorough washing (A) 1 : Keeps warm
2 : Animal fibre 2 : Its leaves are eaten by silkworms
3 : Long thread like structure 3 : Hatches from egg of moth
Sketch the cross section of soil and label the various layers.
Take three test-tubes. Fill æth of each with water. Label them A, B and C. Keep a snail in test-tube A, a water plant in test-tube B and in C, keep snail and plant both. Which test-tube would have the highest concentration of CO2?
Here is a crossword puzzle: Good luck!
Across
3. Liquid waste products
4. Solid waste extracted in sewage treatment
6. A word related to hygiene
8. Waste matter discharged from human body
Down
1. Used water
2. A pipe carrying sewage
5. Micro-organisms which causes cholera
7. A chemical to disinfect water
Sketch the reproductive parts of a flower.
Describe how crystals of copper sulphate are prepared.
Solve the following crossword puzzle with the clues given:
Across
2. Plantation prevents it.
5. Use should be banned to avoid soil pollution.
6. Type of soil used for making pottery.
7. Living organism in the soil.
Down
1. In desert soil erosion occurs through.
3. Clay and loam are suitable for cereals like.
4. This type of soil can hold very little water.
5. Collective name for layers of soil.
Match the items in Column I with those in Column II:
Column I Column II
(i) A home for living organisms (a) Large particles
(ii) Upper layer of the soil (b) All kinds of soil
(iii) Sandy soil (c) Dark in colour
(iv) Middle layer of the soil (d) Small particles and packed tight (v) Clayey soil (e) Lesser amount of humus
When baking soda is mixed with lemon juice, bubbles are formed with the evolution of a gas. What type of change is it? Explain.
Explain why burning of wood and cutting it into small pieces are considered as two different types of changes.
What are decomposers? Name any two of them. What do they do in the forest?
When baking soda is mixed with lemon juice, bubbles are formed with the evolution of a gas. What type of change is it? Explain.
Classify the changes involved in the following processes as physical or chemical changes:
(a) Photosynthesis
(b) Dissolving sugar in water
(c) Burning of coal
(d) Melting of wax
(e) Beating aluminium to make aluminium foil
(f ) Digestion of food
Match the following :
(i) Land breeze blows during (a) summer
(ii) Sea breeze blows during (b) winter
(iii) Dark coloured clothes are preferred during (c) day
(iv) Light coloured clothes are preferred during (d) night
Given below is a crossword puzzle based on this lesson. Use hints to fill in the blank spaces with letters that complete the words.
Down Across
(D) 1 : Thorough washing (A) 1 : Keeps warm
2 : Animal fibre 2 : Its leaves are eaten by silkworms
3 : Long thread like structure 3 : Hatches from egg of moth
Suppose the two photographs, shown in Fig. 13.1 and Fig. 13.2, had been taken at an interval of 10 seconds. If a distance of 100 metres is shown by 1 cm in these photographs, calculate the speed of the blue car.
Distinguish between a parasite and a saprotroph.
Which type of lens forms always a virtual image?
The bulb in the circuit shown in Fig.14.23 does not glow. Can you identify the problem? Make necessary changes in the circuit to make the bulb glow.