Name the reagents used in the following reactions:

(i) Oxidation of a primary alcohol to carboxylic acid.

(ii) Oxidation of a primary alcohol to aldehyde.

(iii) Bromination of phenol to 2,4,6-tribromophenol.

(iv) Benzyl alcohol to benzoic acid.

(v) Dehydration of propan-2-ol to propene.

(vi) Butan-2-one to butan-2-ol.

Give simple chemical tests to distinguish between the following pairs of compounds.

(i) Propanal and Propanone

(ii) Acetophenone and Benzophenone

(iii) Phenol and Benzoic acid

(iv) Benzoic acid and Ethyl benzoate

(v) Pentan-2-one and Pentan-3-one

(vi) Benzaldehyde and Acetophenone

(vii) Ethanal and Propanal

A 5% solution (by mass) of cane sugar in water has freezing point of 271 K. Calculate the freezing point of 5% glucose in water if freezing point of pure water is 273.15 K.

How the following conversions can be carried out?

(i) Propene to propan-1-ol

(ii) Ethanol to but-1-yne

(iii) 1-Bromopropane to 2-bromopropane

(iv) Toluene to benzyl alcohol

(v) Benzene to 4-bromonitrobenzene

(vi) Benzyl alcohol to 2-phenylethanoic acid

(vii) Ethanol to propanenitrile

(viii) Aniline to chlorobenzene

(ix) 2-Chlorobutane to 3, 4-dimethylhexane

(x) 2-Methyl-1-propene to 2-chloro-2-methylpropane

(xi) Ethyl chloride to propanoic acid

(xii) But-1-ene to n-butyliodide

(xiii) 2-Chloropropane to 1-propanol

(xiv) Isopropyl alcohol to iodoform

(xv) Chlorobenzene to p-nitrophenol

(xvi) 2-Bromopropane to 1-bromopropane

(xvii) Chloroethane to butane

(xviii) Benzene to diphenyl

(xix) tert-Butyl bromide to isobutyl bromide

(xx) Aniline to phenylisocyanide

A solution of glucose in water is labelled as 10% w/w, what would be the molality and mole fraction of each component in the solution? If the density of solution is 1.2 g mL^-1, then what shall be the molarity of the solution?

Henry's law constant for CO₂ in water is 1.67 x 10⁸Pa at 298 K. Calculate the quantity of CO₂in 500 mL of soda water when packed under 2.5 atm CO₂ pressure at 298 K.

Calculate the mass of a non-volatile solute (molar mass 40 g mol^-1) which should be dissolved in 114 g octane to reduce its vapour pressure to 80%.

The vapour pressure of pure liquids A and B are 450 and 700 mm Hg respectively, at 350 K. Find out the composition of the liquid mixture if total vapour pressure is 600 mm Hg. Also find the composition of the vapour phase.

Calculate the mole fraction of benzene in solution containing 30% by mass in carbon tetrachloride.

How many mL of 0.1 M HCl are required to react completely with 1 g mixture of Na₂CO₃ and NaHCO₃ containing equimolar amounts of both?

If NaCl is doped with 10^-3mol % of SrCl₂, what is the concentration of cation vacancies?

Using IUPAC norms write the systematic names of the following:

(i) [Co(NH₃)6]Cl₃

(ii) [Pt(NH₃)₂Cl(NH₂CH₃)]Cl

(iii) [Ti(H₂O)6]³⁺

(iv) [Co(NH₃)₄Cl(NO₂)]Cl

(v) [Mn(H₂O)6]²⁺

(vi) [NiCl₄]^2-

(vii) [Ni(NH₃)₆]Cl₂

(viii) [Co(en)₃]³⁺

(ix) [Ni(CO)₄]

Boiling point of water at 750 mm Hg is 99.63°C. How much sucrose is to be added to 500 g of water such that it boils at 100°C.Molal elevation constant for water is 0.52 K kg mol^-1.

How are the following conversions carried out?

(i) Propene → Propan-2-ol

(ii) Benzyl chloride → Benzyl alcohol

(iii) Ethyl magnesium chloride → Propan-1-ol.

(iv) Methyl magnesium bromide → 2-Methylpropan-2-ol.

The decomposition of NH₃on platinum surface is zero order reaction. What are the rates of production of N₂and H₂if k = 2.5 x 10^-4mol^-1L s^-1?

H₂S, a toxic gas with rotten egg like smell, is used for the qualitative analysis. If the solubility of H₂S in water at STP is 0.195 m, calculate Henry's law constant.

What are alloys? Name an important alloy which contains some of thelanthanoid metals. Mention its uses.

The E^θ(M²⁺/M) value for copper is positive (+0.34V). What is possibly the reason for this? (Hint: consider its high Δ_aHV and low Δ_hydHV)

Determine the osmotic pressure of a solution prepared by dissolving 25 mg of K₂SO₄ in 2 liter of water at 25° C, assuming that it is completely dissociated.

In terms of band theory, what is the difference

(i) Between a conductor and an insulator

(ii) Between a conductor and a semiconductor

Ionic solids, which have anionic vacancies due to metal excess defect, develop colour. Explain with the help of a suitable example.