Class 12 Chemistry - Chapter Electrochemistry NCERT Solutions | Given the standard electrode potentials,

If a current of 0.5 ampere flows through a metallic wire for 2 hours, then how many electrons would flow through the wire?

Calculate the emf of the cell in which the following reaction takes place:

Ni_(s) + 2Ag⁺ (0.002 M) → Ni²⁺ (0.160 M) + 2Ag_(s)

Given that E^ø_cell = 1.05 V

Depict the galvanic cell in which the reaction Zn(s) + 2Ag⁺(aq) → Zn²⁺(aq) + 2Ag(s) takes place.

Further show:

(i) Which of the electrode is negatively charged?

(ii) The carriers of the current in the cell.

(iii) Individual reaction at each electrode.

Calculate the standard cell potentials of galvanic cells in which the following reactions take place:

(i) 2Cr(s) + 3Cd²⁺(aq) → 2Cr³⁺(aq) + 3Cd

(ii) Fe²⁺(aq) + Ag+(aq) → Fe³⁺(aq) + Ag(s)

Calculate the ΔrG^ø¸ and equilibrium constant of the reactions.

Write the Nernst equation and emf of the following cells at 298 K:

(i) Mg(s) | Mg²⁺(0.001M) || Cu²⁺(0.0001 M) | Cu(s)

(ii) Fe(s) | Fe²⁺(0.001M) || H⁺(1M)|H₂(g)(1bar) | Pt(s)

(iii) Sn(s) | Sn²⁺(0.050 M) || H⁺(0.020 M) | H₂(g) (1 bar) | Pt(s)

(iv) Pt(s) | Br₂(l) | Br^-(0.010 M) || H⁺(0.030 M) | H₂(g) (1 bar) | Pt(s).

Define conductivity and molar conductivity for the solution of an electrolyte. Discuss their variation with concentration.

How would you determine the standard electrode potential of the system Mg²⁺ | Mg?

Predict the products of electrolysis in each of the following:

(i) An aqueous solution of AgNO₃ with silver electrodes.

(ii) An aqueous solution of AgNO₃with platinum electrodes.

(iii) A dilute solution of H₂SO₄with platinum electrodes.

(iv) An aqueous solution of CuCl₂ with platinum electrodes.

A solution of Ni(NO₃)₂ is electrolysed between platinum electrodes using a current of 5 amperes for 20 minutes. What mass of Ni is deposited at the cathode?

The resistance of a conductivity cell containing 0.001M KCl solution at 298 K is 1500 Ω. What is the cell constant if conductivity of 0.001M KCl solution at 298 K is 0.146 x 10^-3 S cm^-1.

For the reaction R → P, the concentration of a reactant changes from 0.03 M to 0.02 M in 25 minutes. Calculate the average rate of reaction using units of time both in minutes and seconds.

Write the formulas for the following coordination compounds:

(i) Tetraamminediaquacobalt (III) chloride

(ii) Potassium tetracyanonickelate(II)

(iii) Tris(ethane-1,2-diamine) chromium(III) chloride

(iv) Amminebromidochloridonitrito-N-platinate(II)

(v) Dichloridobis(ethane-1,2-diamine)platinum(IV) nitrate

(vi) Iron(III) hexacyanoferrate(II)

(i) Write structures of different isomeric amines corresponding to the molecular formula, C4H11N

(ii) Write IUPAC names of all the isomers.

(iii) What type of isomerism is exhibited by different pairs of amines?

Why are solids rigid?

Write any two characteristics of Chemisorption.

Write the structures of the following compounds.

(i) α-Methoxypropionaldehyde

(ii) 3-Hydroxybutanal

(iii) 2-Hydroxycyclopentane carbaldehyde

(iv) 4-Oxopentanal

(v) Di-sec-butyl ketone

(vi) 4-Fluoroacetophenone

Which of the ores mentioned in Table 6.1 can be concentrated by magnetic separation method?

Why are pentahalides more covalent than trihalides?

Silver atom has completely filled d orbitals (4d10) in its ground state. How can you say that it is a transition element?

Glucose or sucrose are soluble in water but cyclohexane or benzene (simple six membered ring compounds) are insoluble in water. Explain.

The decomposition of dimethyl ether leads to the formation of CH₄, H₂and CO and the reaction rate is given by

Rate = k [CH₃OCH₃]^3/2

The rate of reaction is followed by increase in pressure in a closed vessel, so the rate can also be expressed in terms of the partial pressure of dimethyl ether, i.e.,

 Rate = k (P_CH3OCH3)^3/2

If the pressure is measured in bar andtime in minutes, then what are the units of rate and rate constants?

What is tincture of iodine ? What is its use ?

Mention the factors that affect the rate of a chemical reaction.

What are natural and synthetic polymers? Give two examples of each type.

The conversion of molecules X to Y follows second order kinetics. If concentration of X is increased to three times how will it affect the rate of formation of Y?

Why is sulphuric acid not used during the reaction of alcohols with KI?

Bond angle in PH⁺₄ is higher than that in PH₃. Why?

How the following conversions can be carried out?

(i) Propene to propan-1-ol

(ii) Ethanol to but-1-yne

(iii) 1-Bromopropane to 2-bromopropane

(iv) Toluene to benzyl alcohol

(v) Benzene to 4-bromonitrobenzene

(vi) Benzyl alcohol to 2-phenylethanoic acid

(vii) Ethanol to propanenitrile

(viii) Aniline to chlorobenzene

(ix) 2-Chlorobutane to 3, 4-dimethylhexane

(x) 2-Methyl-1-propene to 2-chloro-2-methylpropane

(xi) Ethyl chloride to propanoic acid

(xii) But-1-ene to n-butyliodide

(xiii) 2-Chloropropane to 1-propanol

(xiv) Isopropyl alcohol to iodoform

(xv) Chlorobenzene to p-nitrophenol

(xvi) 2-Bromopropane to 1-bromopropane

(xvii) Chloroethane to butane

(xviii) Benzene to diphenyl

(xix) tert-Butyl bromide to isobutyl bromide

(xx) Aniline to phenylisocyanide

Classify the following as amorphous or crystalline solids:
Polyurethane, naphthalene, benzoic acid, teflon, potassium nitrate, cellophane, polyvinyl chloride, fibre glass, copper.

What are the factors which influence the adsorption of a gas on a solid?